Do It Right Plumbing
$99 first-time drain cleaning, free camera scope included →Text photos to 602-596-3013 for a free rough estimate →

Plumbing Advice

How Long Does It Take to Install a Water Heater?

By Kenneth Parks ·

Phoenix garage water heater closet with the old tank removed and new flex connectors ready for the install

For a straightforward swap, we install a water heater in about two to three hours. That is a standard tank replacing a standard tank in the same spot with the same fuel. A tankless conversion, a relocation, or a job where the old connections need to be brought up to code can take most of a day. The hours depend less on the heater and more on what we find when the old one comes out.

I am Kenneth Parks, and I have been replacing water heaters around Phoenix since I started with one truck in 2006, with plenty of years in the trade before that. Here is how the time breaks down, so you know what to expect when you schedule.

A Typical Tank Replacement, Step by Step

  • Shut off the water and the gas or power, then drain the old tank. Draining is the slow part, often 20 to 40 minutes on a tank full of Phoenix mineral sediment.
  • Disconnect the water lines, the gas line or electrical, and the vent, and carry the old unit out.
  • Set the new heater, reconnect everything, and replace the parts that should not be reused: flex connectors, the gas sediment trap, the T&P discharge line, and often the shut-off valve.
  • Fill it, purge air at the faucets, light it or power it up, and pressure-test every joint before we leave.

If the install was done right the first time years ago, this moves quickly. If it was not, we slow down and fix it, because the point of the job is a heater that is safe and up to code, not just one that makes hot water.

What Can Make It Take Longer to Install a Water Heater

A few things reliably add time. Switching from a tank to a tankless unit means new gas sizing, a new vent, and often a new electrical outlet, so plan on most of a day. Moving the heater to a new location means running new lines. Older homes sometimes have a gas line that is undersized or a vent that does not meet current code, and I will not connect a new heater to either one. Expansion tanks, earthquake straps where required, and a drain pan with a proper drain line also add a little time, and they are worth it. If the heater is in a tight closet or an attic, getting the old one out and the new one in is slow, careful work.

One thing that adds time is switching fuels, since a new gas line or a new 240 volt circuit has to go in before the heater does. Before you decide whether that switch is worth it, read gas vs electric water heater for a Phoenix home.

One part of a proper install that adds a few minutes and saves a lot of trouble is the expansion tank, which most Phoenix homes with a pressure regulator need. I explain how to tell if yours does in do I need a water heater expansion tank in Phoenix.

A Job in Glendale

A homeowner in Glendale texted us a photo of a leaking tank in a garage closet on a Monday morning. From the picture I could see it was a like-for-like swap, so we brought the right unit on the truck and were done in under three hours, including a new shut-off valve and a drain pan the old install never had. The only surprise was a corroded gas flex connector, which we replaced. She had hot water again before lunch. That is what a photo ahead of time buys you: the right parts on the first trip.

The Honest Counterpoint: Faster Is Not Always Better

I have seen plenty of one-hour installs. They skip the drain pan, reuse old flex lines, leave the T&P line pointed nowhere, and never pressure-test. That heater works on day one and leaks on day 400. We take the extra hour. We also pull the permit when one is required, which adds paperwork but protects you when you sell the house. And if your current heater is not actually at the end of its life, we say so. Our post on how long water heaters last in Arizona helps you judge whether a water heater repair is the smarter move this year.

One more piece of the timeline people forget is the permit. The install itself is done in a few hours, but the city inspection follows on its own schedule, usually a day or two later. I explain what the inspector looks for and why I never skip this step in do I need a permit to replace a water heater in Phoenix.

Call or Text Do It Right Plumbing

When you are ready to install a water heater, the fastest way to get an accurate timeline is to text a photo of your current unit to 602-596-3013 for a free rough estimate. We will tell you whether it is a two-hour swap or a bigger project. Do It Right Plumbing is family owned since 2006, AZ ROC #219450, licensed, bonded and insured, with a 1-year parts and labor warranty on every job and a 6-year manufacturer warranty on the water heaters we install. Learn more about our water heater installation and tankless water heater services, visit Do It Right Plumbing online, or call 602-428-2585.

Water heater installation in Phoenix

See the details

Frequently Asked Questions

Can a water heater be installed the same day?

Usually, yes, for a standard tank replacement. We stock common sizes and can often handle it the day you call, especially if you text a photo first so we bring the right unit.

How long does a tankless water heater take to install?

Plan on most of a day for a conversion from a tank. New gas sizing, venting, and an electrical outlet are usually part of it. Replacing an existing tankless with a new one is much quicker.

How long until I have hot water after installation?

A gas tank heats a full tank in roughly 30 to 45 minutes after lighting. Electric tanks take longer, often an hour or two. Tankless units are ready as soon as they are commissioned.

Need a Plumber Today?

Call 602-428-2585 and talk to a real person, or send us the details and we'll call you back.

Call NowText Photos